Chimiver Ecostar Water Based Floor Lacquer

Chimiver Ecostar Polyurethane Water Based Floor Lacquer | Professional Wood Floor Varnish

Chimiver Ecostar Polyurethane Water Based Floor Lacquer is a premium single-component wood floor finish designed to provide durable, attractive and long-lasting protection for wooden flooring. Combining polyurethane strength with modern water-based technology, Ecostar provides excellent resistance to everyday wear while enhancing the natural appearance of the timber with a warm, professional finish.

Unlike two-component floor lacquers that require a separate hardener to be measured and mixed before application, Chimiver Ecostar is a convenient **single-pack, ready-to-use floor lacquer**. This makes application considerably simpler for professional flooring contractors and experienced DIY users while eliminating concerns about incorrect hardener ratios or limited pot life after mixing.

The high-solids formulation creates a strong protective coating capable of resisting abrasion, foot traffic and everyday wear. It is particularly suitable for residential floors and other compatible wooden surfaces where dependable protection and an attractive finish are required.

Chimiver Ecostar is available in **matt, semi-gloss and gloss finishes**, allowing the appearance of the completed floor to be selected according to the room, timber and personal preference.

## High Quality Polyurethane Protection for Wooden Floors

Wooden flooring needs protection against continuous everyday use.

Shoes, furniture, dust, grit, pets and normal foot traffic gradually wear an unprotected timber surface. Liquids and everyday contamination can also penetrate bare wood much more readily than a properly finished floor.

Chimiver Ecostar creates a protective polyurethane coating over the timber.

The lacquer has high resistance to wear while providing a pleasant final appearance. Once properly applied and cured, the coating protects the timber from normal everyday traffic and makes routine floor maintenance significantly easier.

Its excellent resistance to abrasion also makes it suitable for floors that receive regular use.

The finish retains the natural character of the wood rather than covering the surface with an opaque coating.

## Single Component and Ready to Use

One of the major advantages of Chimiver Ecostar is its simplicity.

This is a **single-component floor lacquer**, meaning there is no separate hardener to add before application.

Open the container, prepare the lacquer appropriately and apply it using the recommended roller or brush.

This provides several advantages on smaller flooring projects. There is no need to calculate a mixing ratio, and unused uncontaminated lacquer has not automatically been activated by adding a hardener.

For homeowners undertaking a carefully planned floor restoration, the single-component format can make Ecostar considerably more approachable than a professional two-pack system.

Professional flooring contractors can also benefit from the convenience on residential and medium-duty projects where a high-quality single-pack polyurethane lacquer provides the required performance.

## Matt, Semi-Gloss and Gloss Finishes

Chimiver Ecostar is available in different sheen levels, allowing the finished appearance to complement the property.

**Matt** provides a contemporary lower-sheen appearance and is an excellent choice where the objective is to maintain a more understated natural-looking wooden floor.

**Semi-gloss** provides additional reflection while retaining a balanced appearance. It works particularly well in traditional and modern interiors where some sheen is desired without creating a highly reflective surface.

**Gloss** creates the strongest shine and highlights the colour and grain of the timber more dramatically.

The appropriate finish is largely an aesthetic decision. All three options allow the beauty and grain structure of the timber to remain visible beneath the protective coating.

## Excellent for Sanded Wooden Floors

Correct preparation is one of the most important stages when applying any professional floor lacquer.

Chimiver Ecostar should be applied to a properly prepared wooden surface.

Old coatings, contamination and significant surface defects should be removed as required. When restoring an existing floor, professional sanding can expose clean timber and create a uniform surface for the new finishing system.

After final sanding, vacuum the floor extremely thoroughly.

Pay particular attention to corners, edges, expansion gaps and spaces between floorboards where fine sanding dust can remain.

The surface must be clean and free from dust, grease, wax, silicone and other substances capable of interfering with adhesion.

Never apply expensive floor lacquer over poorly prepared timber and expect the coating to hide preparation problems.

## Clear and Simple Application Instructions

Chimiver Ecostar is straightforward to apply when the floor has been correctly prepared.

**Step 1 – Prepare the room**

Remove furniture, rugs and movable objects.

Make sure the room and wooden floor are within appropriate application conditions. The recommended application temperature is approximately **10°C to 25°C**.

Avoid excessively hot, cold or humid conditions.

**Step 2 – Prepare the floor**

Sand the wooden floor correctly where required.

Complete the final sanding carefully and vacuum the entire surface thoroughly.

The timber must be clean, dry and free from dust, grease, wax and contamination before lacquering.

**Step 3 – Prepare the lacquer**

Chimiver Ecostar is a **single-component, ready-to-use lacquer**.

No hardener needs to be added.

Mix the lacquer gently and thoroughly before application, taking care not to introduce unnecessary air bubbles.

**Step 4 – Cut in the edges**

Use a suitable high-quality brush to apply Ecostar around edges, corners, door frames and other areas that cannot easily be reached with a roller.

Avoid creating excessively heavy accumulations around the perimeter.

**Step 5 – Roll the main floor**

Apply the lacquer evenly using a suitable microfibre floor lacquer roller.

Work systematically and maintain a wet edge.

Apply the lacquer along the direction of the wood grain where practical and avoid repeatedly rolling areas that have already started drying.

Aim for a smooth, consistent coating without puddles or unnecessarily thick sections.

**Step 6 – Allow the first coat to dry**

Allow approximately **2–4 hours** under suitable conditions before applying the next coat without sanding.

Drying time can vary depending on temperature, humidity, airflow and the amount of lacquer applied.

**Step 7 – Apply another coat**

When recoating within the appropriate 2–4 hour period, the following coat can normally be applied without intermediate sanding.

If the previous coat has been left for approximately **12–24 hours**, lightly sand it with approximately **220-grit abrasive**, then vacuum extremely thoroughly before recoating.

**Step 8 – Apply a third coat if required**

Where the selected finishing system requires three coats, repeat the same procedure.

For an especially smooth professional finish, light intermediate sanding can improve the final surface quality.

## Avoid Applying the Lacquer Too Thickly

More lacquer does not automatically create a stronger or better-looking floor.

Applying excessively thick coats can interfere with proper drying and produce an uneven finish.

Several correctly applied coats provide a much better result than attempting to create the entire protective layer with one extremely heavy application.

Load the roller evenly and distribute the lacquer consistently.

Watch for puddles, heavy roller lines and excessive accumulation around edges.

Good lighting is particularly useful while lacquering because reflections across the wet surface make missed sections and uneven application easier to identify.

## Water Based With Low Odour

Water-based floor lacquer technology provides important practical advantages compared with traditional solvent-heavy finishes.

Chimiver Ecostar has a considerably more user-friendly application profile and is particularly suitable for indoor wooden flooring.

The reduced solvent burden makes water-based technology attractive for occupied residential properties and professional renovation projects where strong lingering solvent smells are undesirable.

Good ventilation should still be provided throughout application and drying.

Water-based does not mean that normal precautions can be ignored. It remains a professional floor coating and should be handled accordingly.

## Warm and Attractive Wood Appearance

Chimiver Ecostar is designed to provide a warm and pleasant appearance once applied.

This is important when choosing a floor lacquer because different finishing products can affect the appearance of timber differently.

The coating enhances the natural character and grain of the wood while providing the protective layer required for everyday use.

Always test the complete finishing system on a small inconspicuous section or sample board first when the final colour and appearance are particularly important.

This is especially advisable on woods containing tannins, including oak and chestnut.

## Suitable for Professional and DIY Applications

Chimiver Ecostar provides an excellent balance between professional-quality performance and straightforward application.

Floor sanding contractors can use it for residential and appropriate commercial restoration projects, while competent DIY users benefit from the convenience of the single-component formulation.

The key to achieving professional results is preparation.

Even the highest-quality lacquer cannot compensate for sanding scratches, residual dust, grease or an unevenly prepared floor.

Take sufficient time preparing the timber, use clean professional application equipment and follow the drying and recoating requirements carefully.

## Safety Instructions

Always use Chimiver Ecostar in a **well-ventilated indoor environment**.

Wear suitable protective gloves when handling and applying the lacquer, and use appropriate eye protection where there is a possibility of splashing.

Avoid unnecessary skin and eye contact.

Keep children and pets away from the work area during application and throughout the drying period.

Do not smoke around floor-finishing products and keep the container properly closed when not in use.

Never mix Chimiver Ecostar with random hardeners, solvents, cleaners or other floor lacquers.

If thinning is genuinely required because of specific application conditions, use only a compatible product recommended for the lacquer rather than experimenting with household solvents.

Store unused lacquer securely in its original labelled container and protect it from unsuitable temperatures.

## Caring for the Finished Floor

Once the lacquer has dried and properly cured, regular maintenance helps preserve the new finish.

Vacuum or sweep frequently to remove grit capable of producing scratches.

Use entrance mats to reduce the amount of abrasive dirt carried onto the floor and fit suitable protective pads beneath furniture legs.

Clean using products specifically designed for lacquered wooden floors rather than aggressive degreasers or highly alkaline general cleaners.

Wipe spills promptly and avoid leaving standing water on wooden flooring.

Correct maintenance can significantly extend the attractive appearance and service life of the lacquer system.

## Why Choose Chimiver Ecostar Polyurethane Water Based Floor Lacquer?

Chimiver Ecostar combines **single-component convenience, polyurethane durability, high solids, excellent abrasion resistance and an attractive professional finish** in one premium water-based wooden floor lacquer.

There is no hardener to measure or mix, making preparation straightforward while still delivering excellent protection against normal wear and foot traffic.

Application is simple: **prepare and vacuum the timber thoroughly, mix the ready-to-use lacquer, cut in the edges with a brush, roll an even coat across the floor and allow approximately 2–4 hours before recoating. If more than 12–24 hours passes between coats, lightly sand with approximately 220-grit abrasive and vacuum thoroughly before continuing.**

Available in **matt, semi-gloss and gloss**, Chimiver Ecostar allows homeowners and flooring professionals to choose the appearance that best complements the timber and interior.

For newly sanded or properly prepared wooden floors requiring a reliable, easy-to-apply and highly durable water-based polyurethane finish, Chimiver Ecostar provides an excellent combination of professional protection, straightforward application and long-lasting appearance.